Rainbow Vacuum E-2 (e SERIES™) GSE Motor Design Parts

Factory OEM motor for the E-2 (e SERIES™) Rainbow system. This motor has been improved in several areas over the years so it will give better performance and durability than your existing motor.

In 1998, Rexair installed two motor versions into the E-2 Rainbow. One was the AME motor and the other was the GSE motor. As time went on, they found that the GSE motor was the superior design and started to install exclusively while discontinuing the AME motor.

In late 2016 a third version motor became available. This is noted as the "E" version and replaces the GSE design. Your original separator and nut will fit all three designs.

*3 year limited warranty (Year 2 and 3 are prorated)

Carbon brush holder kit for the E-2 (e SERIES™) GSE design motor. If you need to replace this, then there is a very high chance that you have an armature issue. Please call technical support with any questions you may have.

Brass separator nut that fits the E-2 (e SERIES™) Rainbow system. Works with the R10827 separator.

DOES NOT fit the E2 Type 12 Rainbow. Confirm that you have a brass nut and not white plastic.

This part separates air from water and allows clean air to flow out through the exhaust and the water to be transferred back to the water pan.

Separator for the single speed E-2 (e SERIES™) Rainbow. Does not fit the E2 Type 12 two speed system.

Effective July 2000, Rexair has improved this separator to increase performance. Inexpensive upgrade to gain improved cleaning ability.

View second image to compare original separator (R7805) with new design.

If your nut that holds this item in place is brass, then this is the correct part. If you have a white plastic nut, then you need to order item number R12103.

Spider nut for the E-2 (e SERIES™) GSE design motor. The GSE has plastic carbon brush holders so you can confirm what model you have.

Spider for the E-2 (e SERIES™) version GSE motor design. An easy way to tell the difference between the AME design and the GSE design is the carbon brush holders. The holders on the AME motor are brass and the GSE motor are plastic.

Lower motor stage housing for the E-2 (e SERIES™) version GSE design motor. If this is damaged, you need to look into why as this part does not wear out.

Fan assembly for the E-2 (e SERIES™) GSE design motor. Be sure to check the center hole is not damaged from rust. Also be sure to confirm that you have a GSE motor and not a AME motor.

Download the schematics for your E-2 Rainbow to be sure what motor design you have. Please call our technical support if you have any questions.

Fan spacer for the E-2 (e SERIES™) GSE design motor. The GSE has plastic carbon brush holders so you can confirm what model you have.

Cooling fan shroud for the single speed E-2 (e SERIES™) GSE version motor. Be sure to understand the difference between the AME and the GSE motor design. Download the schematics to confirm your application.

This is the stage housing clip for the E-2 (e SERIES™) GSE design motor. If you notice that this clip has become rusted, excess moisture is getting into your motor. Call our technical support department to help determine the reason. An easy way to tell the difference between the AME design and the GSE design is the carbon brush holders. The holders on the AME motor are brass and the GSE motor are plastic.

Motor gasket for the early version E-2 (e SERIES™) Rainbow system. Helps seal the motor to the water pan.

Effective through serial number 9230145 with an end date of March 16th 2000.

Works with the R7284 water pan gasket.

UPDATE: This gasket is no longer available as an exact replacement. You have two options, order this item and get a universal factory OEM gasket that does not affect performance and is a direct install, or order an R11316 and R10534 while removing the R7284 original gasket.

Motor mount and water pan gasket for the single speed E-2 (e SERIES™) Rainbow vacuum. Works in combination with the R10534 water pan neck gasket.

Effective serial number 9230146 with a start date of March 17, 2000. Previous version does not have the outer lip and uses a separate gasket that is glued directly to the main housing.

Motor cooling fan for the model E-2 (e SERIES™) version GSE motor design.

Be sure that you understand what version motor you have. The E-2 (e SERIES™) came with both a version GSE and AME. If you need help, call our technical support or view the schematics.

Unless you have the correct equipment to crimp this part into place, we suggest using J-B Weld compound. If this part comes off, it will lead to motor failure.

Bearing bridge for the model E-2 (e SERIES™) Rainbow that fits the GSE version motor. This bearing bridge works with the plastic carbon brush holders. If you have metal carbon brush holders, then you have an AME version motor.

Spring washer that sits on top of the bearing assembly on the E-2 Rainbow This is located just below the bearing bridge. This spring only fits the GSE motor and NOT the AME.

Please confirm if you have a GSE or AME motor before you order.

Original OEM upper bearing for the E-2 (e SERIES™) Rainbow vacuum. This bearing will only fit the GSE version motor.

Location is above the carbon brushes seated inside the bearing bridge.

Can sometimes be difficult to replace as the manufacture presses this bearing onto the armature shaft.

The thermal overload helps protect your model E-2 (e SERIES™) Rainbow vacuum motor.

This part is for the GSE version motor and NOT the AME. Please confirm which version you have before you order motor parts.

If this part fails to reset after 30 minutes due to heat or overuse, it must be replaced.

Original OEM bearing for the E-2 (e SERIES™) Rainbow vacuum. This bearing fits both the AME version motor and also the GSE version.

This bearing is located in the motor base on both motor designs.

The motor base for the E-2 (e SERIES™) model Rainbow. On the early version GSE motor design, the motor base was constructed with a very thin walled bearing pocket that could break easily. Upgrade to this improved design that gives much more support to the lower bearing.

Upper stage for the model E-2 GSE motor design Rainbow vacuum. This stage plate is screwed into place.

Image TWO is the old version that uses the R8309 Stage Support Ring. When ordering this revised item, you can discard the ring as it is no longer needed.

Please confirm which version motor you have before you purchase. If your upper stage is glued into place, then you have an AME version motor.

Upper stage support for the model E-2 GSE motor design Rainbow vacuum.

This stage support is used on the version ONE plate that is screwed into place and the edges are curved towards the water.

Please confirm which version motor and stage you have before you purchase. If your upper stage is glued into place, then you have an AME version motor.