Rainbow Vacuum Power Nozzle R-4375C External View Parts

Right handle that came factory standard on the R-4375C power nozzle electric hose.

Power nozzle handle receptacle for the R-4375C electric hose assembly.

Original OEM factory standard six foot electric hose for your PN-2 and R-4375C model power nozzle. If your hose is torn, then replace only the hose and use your existing handle kit and wand with insert.

Effective June 9th 2000, this item is now a revised replacement for discontinued item numbers R6179, R4145, and R4090.

Standard factory original OEM 8 foot electric hose that fits the following models:

PN-2 / R-4375C / R-2800C* / R-1650C*

*Cord length should be cut down to 43 inches for proper configuration on R-2800C and R-1650C models.

This hose is the second version and has a trigger in the handle to power on/off the brush roll assembly. Allows you to stop the brush roll from turning and go onto bare floors.

Call our technical support team if you have questions on using this with your R-2800C and R-1650C power nozzle. Very easy upgrade and well worth it.

The original part number for the R-4375C power nozzle was R4147. This item is a direct factory replacement.

OPTION: You can order the below items to replace this existing hose. Not the best option but only one available at this time...

Standard Hose (If Needed)

Wand (If Needed)

Extension Cord

Straps (Qty 5)

Total 43 inches, 39 inches outside the main housing, power cord for the R-4375C, R-2800C (Modified) and early versions of the R-1650C model power nozzle.

The R-1650C power nozzle sometimes had a molded shroud that covered the sides of the two prongs. This is not a required feature and has since been discontinued...this cord is now the replacement.

Strain relief bushing for the model R-4375, R-2800, and R-1650 power nozzle. This is an upgrade for the R-2800 and R-1650 power nozzle.

Older version allowed for the power cord to have a sharp bend and would create an electrical short over time. This new version will prevent the problem from happening again.

This is the panel nut which holds the circuit breaker in place for your R-4375C model power nozzle. Only one nut is needed for assembly and can be replaced if lost.

Left handle that came factory standard on the R-4375C power nozzle electric hose.

This handle does not use the trigger system that came out with the PN-2 power nozzle.

This connector is used on various models of the Rainbow, power nozzle, electric hose, etc.

This is the smaller of the two sizes used in various locations.

Insert and wand for the R-4375 non button lock electric hose.

Chrome wand handle for the R-4375C power nozzle. This wand does not have a button and works with the friction fit R5066 power nozzle wand.

Some original chrome wands have R-3113 on the warning label. This is the current revised OEM part.

Long straight wand that includes the channel guide for the R-4375, R-2800, and R-1650 power nozzle.

Length is 31.50 inches (80.01 centimeters)

New version is now stainless steel instead of chrome-plated.

Original 25 inch cord guide for the R8538, R7423, R5661 and R5066 power nozzle wand.

These wands were standard with models PN-2E, PN-2, R-4375, R-2800, and R-1650 power nozzles.

Instructions:

1. Cut the old cord guide in two near the center of the wand.
2. Rip the cord guide away from the wand and rivets.
3. Using flush-cutting end pliers, cut off the rivets.
4. Insure that the wand around the rivet hole is free of burrs.
5. Clean the wand with rubbing alcohol.
6. Remove the paper from the tape on the new cord guide.
7. Place the new cord guide on the wand in the location of the old cord guide, covering the rivet holes and apply pressure at the tape locations.

Main power nozzle housing decal that matches the D4C (Special Edition) Rainbow and R-4375C power nozzle.

This item works with the slide valve to help control air flow. On the high setting, all airflow comes from the vents in the top of the power nozzle.

On the low setting, all the vents are blocked and the air flow is forced to come from the bottom. On high carpet, if all the airflow comes from the bottom, the power nozzle can seem like it is choking and is hard to push.

It is important to have your slide valve in good shape as it helps redirect the airflow to create maximum performance.

Slide valve OEM replacement part for the R-4375C, R-2800C, and R-1650C power nozzle. This item helps redirect airflow for better performance on different length pile carpet.

This small black screw fits all the electric hose handle assemblies from 1990 through current production.

It also fits the newer design AquaMate I system as well as the first and second version PN-2E and PN-2 upright lock clip.