Rainbow Vacuum Power Nozzle R-2800C External View Parts

Replacement cord strap to keep your power cord, that runs from the power nozzle head back the hose and plugs into the main unit, attached to the hose. Standard is five to six straps per application.

Top curved wand for the R-2800C, R-1650C, R-1650A power nozzle. This wand does not have the suction control sleeve.

Even though it might be difficult, your old wand does remove from your standard hose. Twist and pull to remove.

Length is 17.25 inches (44.45 centimeters)

Long straight wand that includes the channel guide for the R-4375, R-2800, and R-1650 power nozzle.

Length is 31.50 inches (80.01 centimeters)

New version is now stainless steel instead of chrome-plated.

Original 25 inch cord guide for the R8538, R7423, R5661 and R5066 power nozzle wand.

These wands were standard with models PN-2E, PN-2, R-4375, R-2800, and R-1650 power nozzles.

Instructions:

1. Cut the old cord guide in two near the center of the wand.
2. Rip the cord guide away from the wand and rivets.
3. Using flush-cutting end pliers, cut off the rivets.
4. Insure that the wand around the rivet hole is free of burrs.
5. Clean the wand with rubbing alcohol.
6. Remove the paper from the tape on the new cord guide.
7. Place the new cord guide on the wand in the location of the old cord guide, covering the rivet holes and apply pressure at the tape locations.

Main power nozzle housing decal that matches the early version D4C Rainbow and R-2800C power nozzle.

This version has more of a glossy finish compared to the later version satin finish.

Main power nozzle housing decal that matches the later version D4C Rainbow and R-2800C power nozzle.

This version has more of a satin finish compared to the early version gloss finish.

This item works with the slide valve to help control air flow. On the high setting, all airflow comes from the vents in the top of the power nozzle.

On the low setting, all the vents are blocked and the air flow is forced to come from the bottom. On high carpet, if all the airflow comes from the bottom, the power nozzle can seem like it is choking and is hard to push.

It is important to have your slide valve in good shape as it helps redirect the airflow to create maximum performance.

Slide valve OEM replacement part for the R-4375C, R-2800C, and R-1650C power nozzle. This item helps redirect airflow for better performance on different length pile carpet.

Factory OEM electric power cord for the R-2800C and R-1650C power nozzle. Total length is 138 inches measuring from outside the power nozzle housing to the tip that plugs into the main unit. You may find this measurement to be off a few inches and that is OK.

Instead of ordering this part, you can upgrade and get an R4121 and R1717, which will allow you to have a break in the cord so you can use one hose for both the power nozzle and small attachments.

If your power nozzle cord has three prongs, please give our tech support team a call at 800-640-2033 to make sure you get the correct part.

NOTE: Please order item numbers R1717 and R4121 as an improved replacement for this item.

Left lens that has a hole for the reset button. Fits the R-2800C power nozzle.

This strain relief has been discontinued and replaced with the improved R4053 design.

This original design was inferior with its short relief which caused a short to form after only a few years of use.

Strain relief bushing for the model R-4375, R-2800, and R-1650 power nozzle. This is an upgrade for the R-2800 and R-1650 power nozzle.

Older version allowed for the power cord to have a sharp bend and would create an electrical short over time. This new version will prevent the problem from happening again.

Genuine OEM factory original 7 foot 18 yarn hose that fits the D4C SE (Special Edition), D4C, D3C, D3A, D2A, D2, and D model Rainbow system. Also was the standard hose for the R-2800C, R-1650C, R-1650A, and R1024 power nozzle.

This hose DOES NOT include the first stage chrome wand. Be sure to remove your curved wand and install it into this new hose.

NOTE: Even though it can be difficult, your old wand does remove from your standard hose. Use a hairdryer to heat up the rubber end of the hose to help remove with a twist and pull method.

Discontinued item numbers include:

• R1777 (D3/D2/R-1650/R1024)
• R2786 (D4/R-2800)
• R4717 9 Yarn (SE)
• R4716 9 Yarn (Hose w/ Molded Tip) (SE)

Hose coupling end that fits into the water pan. For use on the standard hose that fits the models D4C, D3C, D3A, D2A, D2, and D Rainbow.

Hose molded end that fits into the R8400 or R8407 top curved wand. For use on the standard hose that fits the models D4C, D3C, D3A, D2A, D2, and D Rainbow.

Replacement cord strap to keep your power cord, that runs from the power nozzle head back the hose and plugs into the main unit, attached to the hose. Standard is five to six straps per application.

Total 43 inches, 39 inches outside the main housing, power cord for the R-4375C, R-2800C (Modified) and early versions of the R-1650C model power nozzle.

The R-1650C power nozzle sometimes had a molded shroud that covered the sides of the two prongs. This is not a required feature and has since been discontinued...this cord is now the replacement.

Factory OEM replacement power extension cord for R-2800C and R-1650C power nozzle. Total length is 101.5 inches.

One end is a two-prong receptacle the plugs into the power cord coming from the power nozzle. The other end is a two-prong that plugs into the D4C or D3C Rainbow.