Rainbow Vacuum AquaMate I (SE) Optional Equipment Parts

Very rare quick disconnect for all shampoo systems that connect to the faucet. If you have a hard to adapt faucet and are unable to find the correct connection, this item will work! Designed to slip over the end of your faucet and clamp tight to prevent leaks.

Replacement clamp for the R3283 quick disconnect faucet adaptor. Save money and replace the item that is broke and not the entire adaptor.

This faucet kit comes with a variety of gaskets and adaptors to easily fit your Aqua Mate I shampooing system to most standard faucets.

Every kitchen and bathroom sink is different and may require more gaskets than others. This kit will help connect some slight variations or when you need to reduce in order to make proper connection. All the items under the "Included" tab are in this kit.

If you have an outside faucet or a design that doesn't have threads, please view the "Related Items" tab for even more options.

Save 25% by purchasing the kit over purchasing each item separately.

Plastic hose claim for various jobs from adding extra hose to replacing the threaded end nut.

Hose connector to allow you to add any length of supply hose to your AquaMate I system.

If you have a small opening in your faucet and the reducer adaptor does not work, then this item might do the trick.

1. Inspect opening for spout. If opening is clear, proceed to step (2). If opening has a spring insert, remove it with a bent pin or clip by hooking the bent pin on the insert and pulling down. If faucet is equipped with screened screw-cap, remove by unscrewing it.
2. Push adaptor into spout as far as possible. The adaptor should fit snugly in the spout. If adaptor fits loosely, unscrew slotted shaft from knurled nut and replace rubber sleeve with larger sleeve. If adaptor will not fit into spout, unscrew slotted shaft from knurled nut, remove rubber sleeve and brass washer, and replace rubber sleeve with smaller sleeve. Omitting the brass washer.
3. Hold knurled nut stationary with one hand, turn slotted shaft to the left with a coin or screwdriver in slot until securely tightened.

Brass spray nozzle for the AquaMate I cleaning system.

Brass spray nozzle plate for the AquaMate I cleaning system. Works with the R2626 brass spray nozzle.

Shampoo inlet tube for all Rainbow AquaMate I systems.

This tube has been improved over the years to help prevent kinks and soap clogs.

Button lock for the plastic wands that came with the AquaMate I shampooing system. Easy snap in replacement.

Fits the AquaMate II and all version AquaMate I systems.

Upgrade your plastic wands from your AquaMate I to the new stainless steel. Allows you to be more aggressive with cleaning your carpet without the fear of breaking the wands.

Length is 19.25 inches (48.90 centimeters)

A stainless curved wand that works with the non-electrified standard hose. The non-electrified hose came standard with every model Rainbow system except the e2 Black (E2 Type 12) version.

It does have the button lock system on this wand but it does not apply when used on older D4C SE (Special Edition), D4C, D3C, D3A, D2A, D2, and D Rainbow vacuums.

Even though it can be difficult, your old wand does remove from your standard hose. Use a hairdryer to heat up the rubber end of the hose to help remove with a twist and pull method.

Length is 17.25 inches (44.45 centimeters)

Diameter is 1.18 inches (30.09 millimeters) at the tip and 1.25 inches (31.89 millimeters) at the button lock.

The garden connection adaptor kit allows you to hook your AquaMate I system up to a laundry sink or outside faucet that has course threads. You attach this part to the faucet and then your standard hose connection will attach to this part. Comes complete with a gasket for the direct sink connection.