Rainbow Power Nozzle PN-2 PE Series Electric Hose Schematics
This schematic covers the complete PN-2 power nozzle electric hose assembly that includes the handle kit, button lock, and switch actuator.Click on any number below to see more details.
This schematic covers the complete PN-2 power nozzle electric hose assembly that includes the handle kit, button lock, and switch actuator.
Standard factory original OEM 8 foot electric hose that fits the following models:
PN-2 / R-4375C / R-2800C* / R-1650C*
*Cord length should be cut down to 43 inches for proper configuration on R-2800C and R-1650C models.
This hose is the second version and has a trigger in the handle to power on/off the brush roll assembly. Allows you to stop the brush roll from turning and go onto bare floors.
Call our technical support team if you have questions on using this with your R-2800C and R-1650C power nozzle. Very easy upgrade and well worth it.
The original part number for the R-4375C power nozzle was R4147. This item is a direct factory replacement.
Original OEM factory standard six foot electric hose for your PN-2 and R-4375C model power nozzle. If your hose is torn, then replace only the hose and use your existing handle kit and wand with insert.
Effective June 9th 2000, this item is now a revised replacement for discontinued item numbers R6179, R4145, and R4090.
This connector is used on various models of the Rainbow, power nozzle, electric hose, etc.
This is the smaller of the two sizes used in various locations.
Handle kit for the PN-2 and R-4375C power nozzle electric hose. Works with the R5975 actuator switch that came standard on the PN-2 system.
This new handle kit design now uses (7) H566 screws. Older handle kits only used (6). Be sure to confirm and order an extra screw if needed.
When replacing the handle kit on the R-4375C electric hose, you can apply the included insert that covers the section that would allow the use of a switch actuator.
Old item numbers stamped inside handle include, R5759, R5760, R8140, R8141. R4294 is the item number to the warning label on the side.
Insert handle for the original PN-2 and PN-2E electric hose system. Remove screws in handle to replace. If your wand pulls out of the handle easily, then this part could be cracked.
Stainless steel wand and insert for the PN-2 power nozzle electric hose.
Some original chrome wands have R3113 on the warning label. This is a revised OEM factory item.
This small black screw fits all the electric hose handle assemblies from 1990 through current production.
It also fits the newer design AquaMate I system as well as the first and second version PN-2E and PN-2 upright lock clip.
This receptacle can sometimes wear out and the cord does not stay in place. Replacing will fix this issue.
Power nozzle handle receptacle for the PN-2 and R-4375C electric hose assembly.
Electric hose switch that fits in the PN-2E and PN-2 power nozzle.
Actuator spring for the first version PN-2E and PN-2 power nozzle. Works with the R5975 actuator switch.
Actuator switch for the PN-2 model power nozzle electric hose. This trigger uses a metal spring and not a plastic arm to allow movement in handle.
Long straight wand that includes the channel guide for the PN-2 power nozzle.
Length is 31.50 inches (80.01 centimeters)
Straight extension wand with button lock and button hole. This wand works directly with the R5661 standard wand for the PN-2 power nozzle.
Total length is 19 inches for a total of 50 1/2 inches when combined with the R5661 wand.
Great item for reaching those high or hard to reach areas in your home.
Original 25 inch cord guide for the R8538, R7423, R5661 and R5066 power nozzle wand.
Factory original genuine button lock assembly that connects all the metal wands together. This item has had several revisions.
Effective serial number 1160328 domestic and 1685730 international.
The wider current version compared to early production improves the consistency of the button springing back up through the hole.
If your current wand system has a button latch that is pop riveted in, break the old button out of the wand and install this as a replacement. Saves on purchasing a new wand.
Early production and markings:
Current production does not have markings but is the larger of the two sizes above.
Everyone in your family, including those with asthma and allergies, will appreciate the Rainbow® Cleaning System.
Independent laboratory testing has scientifically proven:
The Rainbow® Cleaning System provides certified air cleaning to your home environment.
The Association of Home Appliance Manufacturers (AHAM) certifies that the Rainbow is a proven air cleaner designed to reduce air pollutants that contribute to poor indoor air quality.
The Rainbow® Cleaning System has been evaluated by an independent testing laboratory and has met carpet industry standards for all three elements:
Powerful revolving brushes lift and groom every fiber of your carpet on a cushion of air, leaving it looking like new. The Rainbow does a great job cleaning your carpeting without harming it!